ASTM D3389 PDF

This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.

Author: Zuzragore Gucage
Country: Morocco
Language: English (Spanish)
Genre: Love
Published (Last): 14 January 2004
Pages: 366
PDF File Size: 16.18 Mb
ePub File Size: 20.87 Mb
ISBN: 304-8-22484-121-4
Downloads: 7070
Price: Free* [*Free Regsitration Required]
Uploader: Kagis

This Regulation applies to safety glazing and glazing materials intended for installation as f3389 or other panes, or as partitioning, on power-driven vehicles and their trailers.

The number of cycles that the fabric can endure before fabric shows objectionable change in appearance yarn breaks, pilling, holes is counted. Description of a method e3389 measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin fat in the abraded area.

This European Standard describes the Frick-Taber method for determining the wear resistance of the wear layer of polyvinyl chloride floor coverings d339 laboratory conditions. This standard describes a method for the determination of the abrasion resistance of organic flooring materials when exposed to walking traffic of a revolving nature point abrasion.

It is applicable to non-filled synthetic turf with a pile height greater than 15mm. The test methods included are listed in Table 1. Two test methods are included. Studies have shown that Wyzenbeek test results on the same fabric can and do vary significantly from test to test. This specification covers the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.

The abrasion resistance coating test shall be conducted in accordance with MIL-C The specification applies only to a membrane system that has an integral ashm surface. This test method describes a procedure for determining the astn of image abraded d33389 the surface of a document. Number of cycles determines abrasion rating. It may also have relevance to certain vehicle labels and plastic wood grain film.

Taber Abrasion ASTM D D D

ACT reminds you that there are many points to consider when specifying textiles. This Standard is applicable to the materials and finishes used in the manufacture of food equipment e. This test measures the ability of the decorative surface of melamine surfaces boards to resist abrasive wear-through by rotating a specimen in contact with cylindrical wheels covered with abrasive paper.

  LEY DE HIDROCARBUROS 3058 PDF

This guide covers the selection and use of test methods for high-performance interior architectural wall coatings HIPAC which differ form more conventional coatings in that they are tougher, more stain-resistance, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry, and plaster or gypsum wallboard. NASTA Manufacturing Standards and Specifications for Textbooks If offset printed on coated cover material, a protective top coating for abrasion resistance is required.

My go to reference on the subject asttm the Association for Asttm Textiles. This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods.

Understanding Abrasion Testing

Rotary Platform, Double-Head Taber Method This method is intended for determining the abrasion resistance of cloths in terms of percent change in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction. Corrosion resistance can be increased by sealing the coating, but abrasion resistance is decreased.

Wyzenbeek results abovedouble rubs have not been shown to be an indicator of increased lifespan.

EN Resilient floor coverings – Determination of wear resistance – Part 2: United Nations asmt ECE Regulation 43 Uniform Provisions Concerning the Approval of Safety Glazing Materials and their installation on Vehicles This Regulation applies to safety glazing and glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. LAT Hard Anodizing This method covers the requirements for anodization of aluminum and it alloys MIL-AF 1 Military Specification – Anodic Coatings for Aluminum and Aluminum Alloys This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

Understanding Abrasion Testing – Alendel Fabrics Ltd.

The test is used to determine the desired wear characteristics are met. This procedure covers the determination of the resistance of coatings to abrasion using the Taber Abraser.

  BALLASTLESS TRACK PDF

This method specifies the testing methods for determination of abrasion resistance of rubber, vulcanized or thermoplastic hereafter referred to as “vulcanized rubber”. Fabric samples are mounted flat and rubbed in a figure eight asttm motion using a piece of worsted wool cloth as the abradant. The below links summarize popular Taber test methods and are sorted by application e.

ASTM D3389 – 16

The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer. This guide covers and is intended to assist in establishing procedures for conducting wear tests of rigid or flexible materials utilizing the rotary platform abraser.

Mechanical property of film — Section 9: This guide covers the selection and use of procedures for testing water-borne coatings to be used on exterior, interior or both types of surfaces. This annex specifies the method for measuring abrasion resistance and consequently determining the abrasion class of laminate floor covering elements. Thin, Hard, Dense Deposit This specification covers the engineering requirements for the deposition of a thin, astj dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.

This ast details the NMP best practice for the acceptance and verification of coatings and paint finishes applied to Nokia plastics for the Menu system.

This specification covers metallic stemmed femoral prosthesis used to replace the natural hip joint by means of hemi-arthroplasty or total hip surgical procedures. Tape shall consist of glass spheres of a high optical quality imbedded into a binder on a suitable backing that is pre-coated with a pressure-sensitive adhesive.

This test methods covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone. ISO Annex C Effects of Surface Finish and Colour on Scratch Resistance The test measures the ability of a decorative surface of the sheet under test to resist abrasive wear through to the sub-layer.