IPC JEDEC J STD 033A PDF

IPC/JEDEC J-STDC. Handling, Packing,. Shipping and Use of. Moisture/ Reflow. Sensitive Surface. Mount Devices. A joint standard. IPC/JEDEC J-STDC-1 -. August IPC/JEDEC J-STDC -. February IPC/JEDEC J-STDB.1 includes Amendment 1 -. complies with ipc/JEDEc J-stDA. 3M™ HIC this card meets the IPC /JEDEC J-STD-. A standard. card size: 2” x 3” inches indicates: 5,10,15%.

Author: Zuzshura Faegar
Country: China
Language: English (Spanish)
Genre: Video
Published (Last): 22 March 2013
Pages: 184
PDF File Size: 8.39 Mb
ePub File Size: 20.87 Mb
ISBN: 141-3-15567-434-1
Downloads: 32327
Price: Free* [*Free Regsitration Required]
Uploader: Fautaxe

For standard MBB sizes used for shipping connectors loose or on reels the amount of desiccant required is less than two units. By jexec these procedures, safe and damage-free reflow can be achieved with the dry packing process, providing a minimum shelf life of 12 months from the seal date when using sealed dry bags.

This delamination is 033q referred to as a “blister. The company has analyzed the types of bags that are available for connector packaging and come up with ic recommendations based upon WVTR ratings Table 2.

Already Subscribed to this document. The higher preheat temperatures typical in lead-free solder profiles may provide more safety from blistering for thinner-walled parts than current tin-lead solder profiles due to the direct relationship between moisture desorption rate and temperature.

If the document is revised or amended, you will be notified by email. Some materials currently used may deform melt or show signs of delamination on the side walls, referred to as “blistering. The vapor pressure of moisture and other gases trapped inside the walls of a plastic connector increase rapidly when the connector is exposed to the high temperatures of solder reflow.

Your Alert Profile lists the documents that will be monitored. Many Asian OEMs, who have been converting to the lead-free solder process for the last few years, require that their connectors be packaged to minimize moisture absorption for this reason.

  AKTA DADAH BERBAHAYA PDF

Figures 1 and 2. If all moisture absorption precautions are taken and connectors are still exhibiting some delamination during SMT assembly, measuring the amount of moisture in the parts to determine the steps required to solder without connector blistering may be required.

All techniques provided similar moisture percentages jeedc parts. This standard is also available to be included in Standards Subscriptions.

CARD, HUMIDITY INDICATOR, 5% 10% 15% RH, J-STD-033A

Please first verify your email before subscribing to alerts. As the i;c of the U. BoxEvansville, IN; Fax: Approved options include clay and silica gel. But the problems listed previously for connectors in these hot oven environments can also result in board rework. This standard is not included in any packages.

Minimizing Effects of Lead-free SMT Assembly on Connector Housing Resins

We have no amendments or corrections for this standard. They were subjected to two different storage conditions: Proceed to Checkout Continue Shopping. The company compared three moisture measurement techniques: Table 3 shows that, at the storage conditions of an air-conditioned warehouse in Southeast Asia Condition 1even the thinnest tested LDPE bag would provide enough moisture protection to keep the connectors below the blister ippc level for 90 days.

These methods help avoid damage from moisture absorption and exposure to solder reflow temperatures that can result xtd yield and reliability degradation.

Many connector suppliers are eliminating, or have already eliminated, lead from their contact plating process. In this stage, the higher liquidus temperatures required for lead-free solders may have a profound n on the connector insulator housings. For ease of use, the halogen moisture analyzer was considered the best.

  7939WG WH PDF

icp Board assemblers have focused on handling more expensive ICs but have failed to take similar precautions with board connectors. Blister onset temperature is dependent upon several factors, including wall thickness, percentage of moisture in the part, speed of connector heating, and peak temperature of the reflow process.

Standards & Documents Search

You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Effectiveness of desiccant on moisture absorption of packaged connectors. The next phase m be lead-free solder 03a for board assembly. MBBs in two different thicknesses 0. Lead-free solders result in higher peak temperatures, meaning more blistering. Subscription pricing is determined by: The higher the peak temperature, the lower the moisture content can be before blistering.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Please first log in with a verified email before subscribing to alerts. You may delete a document from your Alert Profile at any time. Higher temperatures required for lead-free SMT soldering will force a change from many currently used connector housing resins, which will melt, suffer pin retention failures or fail to meet dimensional stability requirements.

Key to elimination of blistering is moisture control for most of the temperature-capable engineering resins used in connector housings. The key parameter in blistering of connector housings is the control of moisture absorption in the molded parts.