ASTM A386 PDF

ASTM-A › Zinc Coating (Hot-Dip), Assembled Steel Products. ASTM-A – EDITION – SUPERSEDED — See the following: ASTM-. in Specifications A and A This ASTM Standards A47/ A47M 1 This specification is under the jurisdiction of ASTM Committee A05 on. ASTM AAM Standard Specification for Zinc – Standard A and A shall be done using the metric equivalent of the test.

Author: Tojall Dajas
Country: Iceland
Language: English (Spanish)
Genre: Health and Food
Published (Last): 2 August 2014
Pages: 209
PDF File Size: 16.46 Mb
ePub File Size: 5.1 Mb
ISBN: 576-9-32883-898-1
Downloads: 89812
Price: Free* [*Free Regsitration Required]
Uploader: Yogul

A number in parentheses indicates the year of last reapproval. These designations often apply to specific products, for example A is applicable to cold-heading quality carbon steel wire for tapping or sheet metal screws. For magnetic thickness measurements, specimen excludes any area of the surface which is subject to processes such as? Inspection, Rejection, and Retest 9.

The sample consists of one or more test articles. Such a plan is contained in Test Method B which addresses sampling procedures for the inspection of electrodeposited metallic coatings and related? The thickness of coating thus obtained is the test article coating thickness, or in the case of a specimen removed from a test article, is the specimen average coating thickness.

ASTM Standard List: Coated Steels

Since surface smoothness is a relative term, minor roughness that does not interfere with the intended use of the product, or roughness that is related to the as-received un-galvanized surface condition, steel chemistry, or steel reactivity to zinc 5 sstm. The test method for the new sample shall be selected by mutual agreement between the purchaser and galvanizer.

Where products consisting of various material thicknesses or categories are galvanized, the coating thickness grades for each thickness range and material category of material shall be as shown in Table 1. The other values are based on conversions using the following formulas: Marks in the zinc coating caused by tongs or other items used in handling the article during the galvanizing operation shall not be cause for rejection unless such marks have exposed the base metal and the bare metal areas exceed allowable maximums qstm 6.

A specimen must be evaluated for each steel category and material thickness within the requirements for each specimen of the test article. Metallic coated carbon steel wire coated at size for mechanical springs Composite ribbed steel pipe, pre-coated and polyethylene lined sewer pipe application Flexible poly vinyl chloride PVC gaskets used in connection of water closets to sanitary drainage system.

In such case, the now-smaller lot shall be treated as a new lot for purposes of inspection and acceptance. NOTE 2—The presence in steels and weld metal, in certain percentages, of some elements such as silicon, carbon, and phosphorus tends to accelerate the growth of the zinc-iron alloy layer so that the coating may have a matte?

  IRENA OLCHOWICZ PODSTAWY RACHUNKOWOCI PDF

The mass, shape, and amount of cold working of the astn being galvanized may also affect this condition. Introduction to Total Materia 7 th February Consultation between the designer, fabricator, and galvanizer at appropriate stages in the design and fabrication process will reduce future problems.

For thickness testing purposes, the entire surface area of each unit of product constitutes a specimen. Practice A provides guidance on steel selection and discusses the effects of various elements in steel compositions for example, siliconthat in?

Current edition approved October 10, The pieces shall be handled so that after galvanizing they will not freeze together on cooling. In the case of orders in SI units, all testing and inspection 1 This speci? This article contains a list of standards that covers among other things: Surfaces that remain uncoated after galvanizing shall be renovated in accordance with the methods in Practice A unless directed by the purchaser to leave the uncoated areas untreated for subsequent renovation by the purchaser.

NOTE 5—Inaccessible surface areas are those which cannot be reached for appropriate surface preparation and application of repair materials as described in Practice A NOTE 9—Although some material may be formed after galvanizing, in general the zinc coating on the articles covered by this speci?

The elements a836 be added to the galvanizing bath as part of a pre-alloyed zinc feed, or they can be added to the bath by the galvanizer using a master feed alloy.

This new sample shall be measured using magnetic thickness gages which have been calibrated for accuracy against reference material thickness standards. The requirements for malleable atsm castings to be galvanized shall be as stated in Speci?

In the case of orders in SI units, the values in Table 1, shall be applicable as metric units in micrometres.

For thickness testing purposes, articles whose surface area is greater than in. Total Materia remains the only tool which will be used for this purpose. Search Knowledge Base Enter a phrase to search for: Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. If the lot is found to be nonconforming by the new sample, the galvanizer has atm right to sort the lot for conforming articles by individual test, to re-galvanize nonconforming articles, or to renovate the nonconforming articles in accordance with 6.

  BERZANSKI INDEKSI PDF

Gas Nitriding of Titanium Alloys: Internal threads are not prohibited from being tapped or retapped after galvanizing. The adhesion shall be considered inadequate if the coating?

To get started, click on the standard list button in the menu bar.

ASTM Standard List: Coated Steels :: Total Materia Article

Introduction to Total Materia Integrator 7 th March For test by the purchaser after delivery, the lot consists of the single order or the single delivery load, whichever is the smaller, unless the lot identity, established in accordance a86 the above, is maintained and clearly indicated in the shipment by the galvanizer. For a unit of product whose surface area is equal to or less than in. It is the responsibility of the purchaser to heat treat or otherwise allow for the possibility of such embrittling phenomena.

Finding ASTM materials and standards from specific designation systems in the Total Materia database With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away. The weight of coating per unit area thus determined is converted to equivalent coating thickness values according to Table 2 rounding up or down as appropriate.

Our mission is simple; to make Total Materia the one-stop place and first choice of engineers world wide. Total Materia has allowed us to solve in a definite way all problems we had for the search of alternate materials in foreign countries. For each specimen as described in 3.

If the lot size is such that the sample size cannot be doubled, then the sample size shall be as previous, but the number of widely dispersed sites at which measurements were made shall be doubled, and these sites will constitute the new sample. Within the text of this speci? With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away.

However, by agreement the purchaser is not prohibited from making tests which govern the acceptance or rejection of the materials in his own laboratory or elsewhere.

The average of the? Metallic coated carbon steel wire coated at size for mechanical springs Composite ribbed steel pipe, pre-coated and polyethylene lined sewer pipe application Flexible poly vinyl chloride PVC gaskets astj in connection of water closets to sanitary drainage system For more information on the ASTM designation system see our related article: