FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS
|Published (Last):||10 July 2011|
|PDF File Size:||10.83 Mb|
|ePub File Size:||5.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Water is being filled and retained between the two valves during the induction stroke armature is pulled against the springwater is then pushed out by the action of compressed spring and the armature when the electric-field is shut-off, high pressure is the product of spring force and the cross-section area of the armature tip. It is normally fitted to the vacuum side of the inlet manifold 2D mode for applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor is available.
The water-pump is activated when an adjustable pressure switch, fitted to the inlet manifold, reaches its preset point: Refinements such as flow rate and block jet detection can easily be obtained with a minimum of signal conditioning parts, to achieve a fully integrated water injection system with diagnostic capablities.
Retired System Information
In reference to the schematic diagram on the bottom of this page, the only parts asuamist require interfacing is the HSV High Speed Valve. Electrical and Mechanical specifications Condition Input Voltage: Of course a pressure of at least 3 bar is required.
Aqiamist in for more lists. Peak pressure can go as high as psi! RACE PUMP INFO We have ruled out the widely available centrifugal pump as the pumping mechanism, because it is always coupled to a high rotational-speed drive-motor for efficiency reasons, hence it is prone to wear; further aquxmist arises when the water inside the pump hs-6 frozen, the drive motor has to be detached from the vane by a slipping clutch arrangement so drive-motor windings cannot be damaged as a result of jamming, this led to unnecessary expenses and complicated mechanical links.
Water travels through these grooves, acquiring a swirling motion before leaving the small hole on the tip: Two colored LEDs are mounted on the top side of the box. MF2 MF2 is the brain of the system, ultimately responsible for the vital functions of metering the auamist delivery rate.
Delivery time is estimated using our proprietary method which is based on the buyer’s proximity to the item location, the shipping service selected, the seller’s shipping history, and other factors.
In hard water areas, occasionally clean the filter in a small glass of diluted household lime-remover. Add to watch list. The MF2 uses incoming RPM and pressure signals from the sensors in the engine bay and compares them with a pre-programmed map set by the user.
The new design is also one of the easiest to install as well. See full item description.
For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees. The similarity ends when the manual pump actions is replaced by hfz-6 fields and speed is also cranked up to about 50 strokes a second!
Below you will find technical info and original sales info for the systems. For additional information, see the Global Shipping Program terms aquamisy conditions – opens in a new window or tab.
Delivery times may vary, especially during peak periods. Water travelling through these grooves picks up a swirling motion before leaving the small hole on the tip, causing an atomising effect, turning the water into a fine mist: The valve is terminated with water proof sealed connectors IP The green LED indicates successful detection of fuel injection pulses and the red LED lights up when water is being injected preset manifold pressure is reached. For applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor are available, the MF2 can read these signals and perfom 3-D mapping functions.
The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our latest High speed Valve HSV.
Its primary function was to regulate the water pressure during injection and idle periods set at 5 bars. Sold under 3 versions, the V8V9 and V10, many systems are still operational in the aqamist. For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you.
Aquamist HFS-6 Methanol/Alcohol/Water Injection System- Subaru WRX/STI Ready | eBay
Thread size of the jet is M8x0. Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all the necessary hardware to form the basis of a starter kit.
Aquamist 2c The 2c is designed for stand-alone EMS systems. With the best failsafe aquamost in the industry, and a standard 13ohm injector that could be be driven by a spare PWM channel from your EMS, the HFS-5 easily integrates into nearly any application.
Back to home page.
Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list. Seller assumes all responsibility for this listing.
As the pulsed signal from the pressure switch is directly proportional to the flow of water, it can either be recorded by an on-board data acquistion system for diagnostic purposes or read by the control ECU to monitor blockage or water jet and other faults that may arise.
Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab. Water is then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry.