procedures for installing and wiring the SYSDRIVE 3G3FV-j-CUE/EF3HV-j-CUE Please read this manual thoroughly and handle and operate the product with. The SYSDRIVE 3G3FV is OMRON’s new special-purpose inverter. It provides the harmony between performance, versatility, and simplicity. Using a unique. Manuals and User Guides for Omron SYSDRIVE 3G3FV. We have 1 Omron SYSDRIVE 3G3FV manual available for free PDF download: User Manual.

Use this delay to make any preparations for the change in the control mode. Initialize the torque limit parameters H to H Chapter 2 Installation Never Short or Ground Output Terminals If the output terminals are touched with bare hands or the output wires come into contact with the Invert- er casing, an maanual shock or grounding will occur. Also, be careful not to short the output wires.

Page – If the slip compensation function has lo If the setting is increased too much, the current can fall to the point where stalling occurs. Braking resistor Inverter Caution Valid access levels Parameter Display name Table Of Contents Page numbers refer to the previous version. Parameter Display name Setting Chapter 4 Trial Operation The following is a setting example for a V class Inverter with an input voltage of V.

Chapter 5 Basic Operation Note The voltage settings shown in parentheses are the values for the V class. Energy-saving Control Function Chapter 6 Advanced Operation This parameter can be changed during operation, but normally no adjustments are required. Please read this manual thoroughly and handle and operate the product with care.

Chapter 2 Installation H Direction and Dimensions Install the Inverter on a vertical nanual so that the characters on the nameplate are oriented upward. If a load is connected when auto-tuning is performed, not only will incorrect motor parameters be re- corded, but the motor may operate erratically resulting in dangerous conditions such as loads falling from vertical axis motors. Chapter 6 Advanced Operation Parameter Settings The following table shows the setting information for the multi-function outputs.

External Fault Input level Detection method Alternatively, cables can be routed through a grounded metal pipe to prevent induction 3v3fv. Setting Motor Parameters Checking Before Unpacking Chapter 8 Maintenance Operations The Inverter is not in operation mode. Chapter 3 Preparing for Operation Example The following example shows how to change parameter A to select Flux Vector control vector con- trol with pulse generator. Chapter 2 Installation Note The carrier frequency setting range varies depending on the Inverter capacity.

Omron SYSDRIVE 3G3FV User Manual

There is a heat source nearby. Auto-tuning 3g3fb the only setting for basic operation with open-loop vector control. Four acceleration times and four deceleration times can be set. Page Chapter 4 Trial Operation Monitor Function Chapter 1 Introduction H Dwell Function By holding the output frequency for a constant time during acceleration and deceleration, acceleration and deceleration can be performed without stepping out even when driving a motor with a large start- up load.

Page Chapter 5 Basic Operation The multi-function analog outputs have the following functions with these parameter settings. Program Only the parameters specified in A through A can be set or displayed. Select the setting with the desired combination. Caution Do not pull on the cables. Chapter 6 Advanced Operation Set the power-loss ridethrough time in seconds.

Chapter 8 Maintenance Operations The motor stops during acceleration or when a load is connected.

Omron SYSDRIVE 3G3FV Manuals

Chapter 6 Advanced Operation Note When the S-curve characteristic time is set, the acceleration and deceleration times will be lengthened as follows: Chapter 1 Introduction The 3G3FV allows the following three kinds of access levels to be set in order to further simplify pa- rameter setting. Chapter 6 Advanced Operation Be sure to set the jump frequency so that d d d Multi-function analog output 1 terminal Chapter 5 Basic Operation H Presetting Frequency Reference Values d through d Parameters d through d contain preset reference values 1 through 8.

Three lead-in wire holes 22 dia. Chapter 6 Advanced Operation With this setting, the multi-function input resets faults that have occurred. Disabled Runs as set. Preparing For Operation Maintenance And Inspection Page 66 Chapter 2 Installation H Countermeasures against Harmonics With the continuing development of electronics, the generation of harmonics from industrial machines has been causing problems recently.

Chapter 6 Advanced Operation If the output torque at low speed is a problem i. Ter- minal 22 is the multi-function analog output common. Page Chapter 9 Specifications Dimensions mm Reference Parameters List VSG Page 33 – Chapter 2. Coast to a stop.